I want to connect my HP Envy 5642 to my computer. How do I do this?

The Envy 5642 from HP

The HP ENVY 5640 e-All-in-One Printer Series software and drivers are available for free download and installation right here. Take a look at the paper and make sure it is on a flat surface before printing. Make adjustments to the paper settings and clean the paper feed rollers in the print driver. You may also need to have your printer serviced to resolve this issue.

Before reloading the paper, check its condition.

1. When the paper is bent, wrinkled, curled, dirty, or damaged, it may cause problems with paper feeding. To solve this issue, follow the steps outlined in the section below.
2. To meet the requirements of your , use high-quality paper.
3. Cool, dry storage is best for all documents. If the paper is stored in a moist environment, problems with the feed may arise.
4. Don’t re-feed paper that’s been printed. The ink’s dampness may cause the paper to stay together.
5. Wait for the message “load paper” to appear before reloading the paper.

To check the quality of your paper

1. Make sure your paper is in excellent shape and placed properly in the input tray. It’s also important to make sure that the paper tray is clear of any obstructions.
2. Disconnect the printer’s power cord while you keep it connected to continue printing.
3. Remove the paper stack from the tray.
4. Remove any obstructions from both the tray’s interior and exterior. To see if there is anything in the way of the paper, shine a flashlight over the area. Paper feed problems can be caused even by the smallest fragments of paper.
5. Examine the condition of the sheets you’ve placed in the tray to check whether any of them are bent, curled, ripped, wrinkled, or dusty. If there is any left in the tray, remove it.
6. Please make sure that all of the paper in the stack is of the same kind and size before moving on. Sheets loaded must be the same width and length. There should be no variation in the size of the paper that is utilized. Processors can only handle a single sort of paper at a time.
7. The sheets’ corners should be in alignment and the surface should be smooth.
8. There should be no less than ten or more than twenty-five sheets in each ream of paper.

Keep Your HP Envy 5642 Printer on a Smooth Surface

1. Make sure your printer is facing you.
2. Printing equipment should have a clean environment surrounding and beneath it.
3. The input tray was blocked with paper shards.
4. Books, pencils, pens, and paper are examples of hard and little products.
5. For example, the surface of a carpet or a placemat may be uneven or spongy.
6. Get rid of any obstacles that may be in the way.
7. Put your printer back where it belongs.
8. Ensure that the cable is plugged into the printer’s backside.
9. Press OK to get rid of any alerts that may have appeared on your printer’s control panel.

Re-insert the paper in the feeder

1. A-4-sized pieces of paper can be loaded into the scanner. Place the glossy or printed side of the paper cup in the tray.
2. Open the door and drag it in the desired direction to extend the paper tray.
3. After extending the extender, lift the paper catch.
4. Slide the paper guides out of the way.
5. In front of you, place a ream of white paper with the short end facing up.
6. Make sure the tray is inserted and pressed into place until it snaps into position.

Print out your printer’s status report.

1. Press the down arrow on your printer’s control panel, then pick tools, and then OK.
2. To print your printer’s status report, press the arrow and pick OK. After that, the printer will print a test page for you to verify everything is working properly.
3. After printing a test sheet, proceed to the next step.
4. For HP Envy printers that fail to print the test page, try the following remedy to resolve the problem.

Try To Print A Copies Of The Original Document In Step 6

An original document can be printed if the test page does not work. Once the paper is printed, the error will be corrected in a couple of seconds.